Makita Power Screwdriver 6833 User Manual

Auto Feed Screwdriver  
MODEL 6833  
MODEL 6834  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
 
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
3
 
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
could result in a risk of injury.  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB004-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to screwdriver safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
make exposed metal parts of the tool live”  
and shock the operator.  
3. Hold the tool firmly.  
4. Keep hands away from rotating parts.  
5. Do not touch the bit or the workpiece  
immediately after operation: they may be  
extremely hot and could burn your skin.  
2. Always be sure you have a firm footing.  
Be sure no one is below when using the  
tool in high locations.  
4
 
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
SYMBOLS  
USD201-2  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
A .......................amperes  
....................Class II Construction  
Hz .....................hertz  
.../min................revolutions or reciprocation per  
minute  
................alternating current  
5
 
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
002629  
Switch action  
CAUTION:  
1
2
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
To start the tool, simply pull the switch trigger. Release the  
switch trigger to stop.  
1. Lock button  
For continuous operation, pull the switch trigger and then  
push in the lock button.  
2. Switch trigger  
To stop the tool from the locked position, pull the switch trig-  
ger fully, then release it.  
002636  
Reversing switch action  
This tool has a reversing switch to change the direction of  
rotation. Press the upper side (FWD side) of the reversing  
switch for clockwise rotation or the lower side (REV side) of  
the reversing switch for counterclockwise rotation.  
1
CAUTION:  
Always check the direction of rotation before operation.  
1. Reversing switch  
Use the reversing switch only after the tool comes to a  
complete stop. Changing the direction of rotation before  
the tool stops may damage the tool.  
002648  
Hook  
The hook is convenient for hooking the tool to your belt. It  
can be installed on either side of the tool. To remove it, pull it  
out in the direction of the arrow while raising. To install the  
hook, push it down until it clicksinto place on the tool.  
1
1. Hook  
6
 
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
Installing or removing the bit  
002656  
Loosen the thumb screws which secure the casing. Pull out  
the casing in the direction of the arrow.  
1
2
1. Casing  
2. Thumb screw  
002657  
Press the dust cover toward the plain bearing and pull out  
the bit. If the dust cover cannot be moved as far as the plain  
bearing, try it again after turning the bit slightly.  
1 2  
To install the bit, insert it into the socket while turning it  
slightly. After installing, always make sure that the bit is  
securely held in place by trying to pull it out.  
3
1. Dust cover  
2. Plane bearing  
3. Bit  
002663  
Setting for desired screw length  
There are 3 (for Model 6833) or 5 (for Model 6834) positive-  
lock screw length settings. To obtain the desired setting, pull  
out the stopper base while depressing the lever until you see  
the number of the desired screw length (indicated on the  
plate) appear to rest on the very top edge of the casing. See  
the table below for the relation between the number indicated  
on the plate and the respective screw length ranges.  
1
2
3
4
1. Lever  
2. Stopper base  
3. Plate  
Number indicated  
Screw length range  
on the plate  
25/28  
32  
4. Casing  
25 mm (1) - 28 mm (1 - 1/8")  
28 mm (1 - 1/8) - 35 mm (1 - 3/8)  
35 mm (1 - 3/8) - 41 mm (1 - 5/8)  
41 mm (1 - 5/8) - 51 mm (2)  
51 mm (2) - 57 mm (2 - 1/4)  
40  
* 51  
* 57  
(Note) * for Model 6834 only  
7
 
002665  
Adjusting the driving depth  
5mm (3/16")  
Depress the stopper base as far as it will go. While keeping it  
in this position, turn the adjusting knob until the bit tip  
projects approx. 5 mm (3/16) from the stopper base. Drive a  
trial screw. If the screw head projects above the surface of  
the workpiece, turn the adjusting knob in the A direction; if  
the screw head is counter-sunk, turn the adjusting knob in  
the B direction.  
1
2
3
B
A
1. Stopper plate  
2. Casing  
3. Adjusting knob  
002666  
Installing screw strip  
1
Insert the screw strip through the screw guide. Then insert it  
through the feeder box until the first screw reaches the posi-  
tion next to the driving position.  
2
3
1. Feeder box  
2. Screw strip  
3. Screw guide  
002667  
1
1. Driving position  
8
 
002668  
Removing screw strip  
To remove the screw strip, just pull it out in the direction of  
the arrow. If you depress the reverse button, you can pull out  
the screw strip in the reverse direction of the arrow.  
002669  
1
1. Reverse button  
002671  
Extension handle (optional accessory)  
1
Use of extension handle allows you to drive screws into  
floors while standing.  
1. Extension handle  
9
 
OPERATION  
002676  
Driving operation  
Switch on the tool by pressing the switch trigger and at the  
same time pushing the lock button. Hold the tool squarely  
against the workpiece and apply forward pressure to the tool.  
The screw will be automatically carried to the driving position  
and driven into the workpiece.  
NOTE:  
Do not fire the tool without screws. This will damage the  
workpiece.  
If the feeder box becomes sluggish in operation, spray  
car wax (spray type wax) on its sliding surfaces. Never  
lubricate it.  
001887  
Driving in corner  
This tool can be used to drive at a position 15 mm (5/8)  
away from the wall as shown in the figure.  
2
1
CAUTION:  
Driving at a position closer than 15 mm (5/8) to the wall  
or driving with the stopper base in contact with the wall  
may damage the screw heads and cause wear on the  
bit. This may also lead to poor fastening of screws and  
malfunction of the tool.  
15mm(5/8")  
1. Stopper base  
2. Wall  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
10  
 
002686  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
1
2
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
1. Screwdr  
2. Brush holder cap  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Phillips bit  
Extension handle  
Plastic carrying case  
11  
 
Memo  
12  
 
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
 
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
 
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ALABAMA  
COLORADO  
KENTUCKY  
NEW MEXICO  
PUERTO RICO  
2365 Pelham Parkway  
Pelham, AL 35124  
(205) 620-1791  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
1215 S. Hurstbourne Parkway  
Louisville, KY 40222  
(502) 326-3740  
5805 Menaul Blvd. NE  
Albuquerque, NM 87110  
(505) 881-4619  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
ARIZONA  
CONNECTICUT  
508 Spring St.  
Windsor Locks, CT 06096  
(860) 292-6405  
LOUSIANA  
NEWYORK  
TENNESSEE  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
5626 Jefferson Hwy.  
Harahan, LA 70123  
(504) 733-4138  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
4655 Nolensville Rd.  
Nashville, TN 37211  
(615) 331-9922  
131-35 31st Ave.  
Flushing, NY 11354  
(718) 886-0971  
ARKANSAS  
FLORIDA  
MARYLAND  
TEXAS  
Shackleford Shopping Center  
240 South Shackleford Rd.,  
Ste. C  
620 Douglas Ave. Suite 1302  
Altamonte Springs, FL 32714  
(407) 774-6000  
7541 - 45 Ritchie Highway  
Glen Burnie, MD 21061  
(410) 590-0160  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
Little Rock, AR 72211  
(501) 224-5733  
NORTH CAROLINA  
3501-G S. Tryon St.  
Charlotte, NC 28217  
(704) 527-0611  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(617) 461-9754  
CALIFORNIA  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
Thompson Center Waters  
5501 W. Waters Ave., Ste. 406  
Tampa, FL 33634  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
OHIO  
6253 E. Main St.  
Columbus, OH 43213  
(614) 860-0222  
(813) 886-8292  
MICHIGAN  
1421 N. Clovis Ave., Ste. 112  
Fresno, CA 93727  
(559) 252-5166  
37454 Ann Arbor Trail  
Livonia, MI 48150  
(313) 432-1012  
UTAH  
GEORGIA  
6379 Pearl Road  
Parma Heights, OH 44130  
(440) 843-7555  
145 E. 1300 S., Ste. 101  
Salt Lake City, UT 84115  
(801) 359-3410  
4680 River Green Parkway  
Duluth, GA 30096-2566  
(770) 476-8911  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
1617 E. Kemper Rd.  
Sharonville, OH 45246  
(513) 771-0788  
VIRGINIA  
5760 Northampton Blvd,. Ste.  
102  
Virginia Beach, VA 23455  
(757) 460-0280  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
HAWAII  
4510 Salt Lake Blvd., Suite A7  
Honolulu, HI 96818  
(808) 847-0038  
MISSOURI  
OKLAHOMA  
1440 South EStreet  
San Bernardino, CA 92408  
(909) 885-1289  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
552 E. Memorial Road  
Oklahoma City, OK 73114  
(405) 752-2655  
ILLINOIS  
WASHINGTON  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
22220 84th Ave. So., Bldg. A  
Kent, WA 98032  
(253) 395-8055  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
NEBRASKA  
OREGON  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
828 19th Avenue., N.W.  
Portland, OR 97209  
(503) 222-1823  
1714 E.McFadden Ave., Unit M  
Santa Ana, CA 92705  
(714) 667-5066  
INDIANA  
WISCONSIN  
8403 Michigan Road, Unit 1  
Indianapolis, IN 46268  
(317) 334-9980  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
PENNSYLVANIA  
Springwater Plaza  
364 Wilmington W. Chester  
Pike  
Glen Mills, PA 19342  
(610) 459-4122  
1565 Winchester B.  
Campbell, CA 95008-0501  
(408) 379-0377  
(414) 541-4776  
KANSAS  
8819 W. 95th St.  
Overland Park, KS 66212  
(913) 642-1111  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
NEW JERSEY  
6200 Babcock Blvd  
Pittsburgh, PA 15237  
(412) 366-6363  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
CUSTOMERS RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealers Name & Address  
Model No.  
Serial No.  
15  
 
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of  
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF  
THIS WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
884144C064  
 

Land Pride Lawn Mower FDR2560 User Manual
Lenovo Personal Computer 9965 User Manual
LevelOne Switch POH 0850TX User Manual
LG Electronics CRT Television 29FS2AMB ANX ZE User Manual
Lincoln Electric Welding System 400 MS User Manual
Lindy Switch U8 User Manual
Lowrance electronic Marine Instruments EP 90R User Manual
Mackie Musical Toy Instrument 16v2 User Manual
Makita Cordless Drill 8411D User Manual
Marshall electronic Digital Photo Frame CV340 User Manual