Harbor Freight Tools Power Screwdriver 91332 User Manual

CORDLESS SCREWDRIVER SET  
3.6 VOLT RECHARGABLE  
91332  
ASSEMBLY AND OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
5. Use the right tool for the job. Do not attempt to force a small tool or  
attachment to do the work of a larger industrial tool.There are certain  
applications for which this tool was designed. It will do the job better and  
more safely at the rate for which it was intended. Do not modify this tool and  
do not use this tool for a purpose for which it was not intended.  
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught  
in moving parts. Protective, electrically non-conductive clothes and non-skid  
footwear are recommended when working. Wear restrictive hair covering to  
contain long hair.  
7. Use eye and ear protection. Always wear ANSI approved impact safety  
goggles.  
8. Do not overreach. Keep proper footing and balance at all times. Do not  
reach over or across running machines.  
9. Maintain tools with care. Keep tools sharp and clean for better and safer  
performance. Follow instructions for lubricating and changing accessories.  
Inspect tool cords periodically and, if damaged, have them repaired by an  
authorized technician.The handles must be kept clean, dry, and free from oil  
and grease at all times.  
10. Disconnect power. Unplug Charger Adapter when not in use.  
11. Remove adjusting keys and wrenches. Check that keys and adjusting  
wrenches are removed from the tool or machine work surface before  
operating tool.  
12. Avoid unintentional starting. Be sure the switch is in the Off position when  
not in use and before plugging in. Do not carry any tool with your finger on  
the trigger.  
13. Stay alert. Watch what you are doing, use common sense. Do not operate  
any tool when you are tired.  
15. Check for damaged parts. Before using any tool, any part that appears  
damaged should be carefully checked to determine that it will operate  
properly and perform its intended function. Check for alignment and binding  
of moving parts; any broken parts or mounting fixtures; and any other  
condition that may affect proper operation. Any part that is damaged should  
be properly repaired or replaced by a qualified technician. Do not use the tool  
if any switch does not turn On and Off properly.  
16. Guard against electric shock. Prevent body contact with electrical circuits  
when using this tool.  
SKU 91332 Download from Www.SomanuPalsa.cgoem3. All Manuals Search And Download.  
17. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty. Only use  
accessories intended for use with this tool. Approved accessories are  
available from Harbor Freight Tools.  
18. Do not operate tool if under the influence of alcohol or drugs. Read  
warning labels if taking prescription medicine to determine if your judgment or  
reflexes are impaired while taking drugs. If there is any doubt, do not operate  
the tool.  
19. Maintenance. For your safety, service and maintenance should be  
performed regularly by a qualified technician.  
20. People with pacemakers should consult their physician(s) before using  
this product. Electromagnetic fields in close proximity to a heart pacemaker  
could cause interference to or failure of the pacemaker.  
In addition, people with pacemakers should adhere to the following:  
Avoid operating power tools alone.  
Don’t use a power tool with the power switch locked on.  
Properly maintain and inspect all tools before use to avoid electrical shock.  
Note:Performance of this tool may vary depending on variations in battery power.  
Warning:The warnings, cautions, and instructions discussed in this instruction  
manual cannot cover all possible conditions and situations that may occur. It  
must be understood by the operator that common sense and caution are fac-  
tors which cannot be built into this product, but must be supplied by the opera-  
tor.  
Unpacking  
When unpacking, check to make sure the that all following parts are included. If  
any parts are missing or broken, please call Harbor Freight Tools at the number on  
the cover of this manual.  
Cordless  
Screwdriver  
Accessory Bits  
and Adapters  
Charger  
Adapter  
SKU 91332 Download from Www.SomanuPalsa.cgoem4. All Manuals Search And Download.  
Operation  
Battery Precautions  
1. To avoid accidents, only charge the supplied batteries. Do not use a different  
charger adapter with this tool.  
2. Do not expose the battery to rain or wet conditions.  
3. To avoid damage of cable and plug, never pull the cable to disconnect the  
charger.  
4. Do not charge the battery if either the cable or plug are damaged.  
5. Repairs should be carried out by a qualified technician only.  
6. Do not touch the battery poles with any conductive source.  
7. Do not store the battery in a box with other metal objects.  
8. Do not throw the battery in a fire.  
Charging the Battery  
The internal Battery does not come charged from the factory. Charge before  
using.  
1. Insert the Charger Adapter module plug into the unit connector as shown  
below.  
Note: Never over-discharge a battery by using the tool  
even after tool performance is decreasing. Severe heat  
is most destructive to a battery; the more heat  
generated, the faster the battery loses power.  
A battery that gets too hot can be permanently  
damaged. Never attempt to discharge a tool’s  
battery by continuing to pull the tool trigger.  
When tool performance begins to diminish, stop  
the tool and re-charge the battery for optimal performance.  
2. Plug the Charger Adapter module into an electrical outlet.  
The red LED on the cordless Screwdriver will light. Charge the new battery  
from 5 to 7 hours. Battery usage time will ramp up as the new Battery is  
used, and recharged. Do not overcharge the battery.  
Caution: Never charge Battery for more than 7 hours continuously. Charger  
Adapter should not be left plugged in or charging for more than 7 hours.  
SKU 91332 Download from Www.SomanuPalsa.cgoem5. All Manuals Search And Download.  
3. Remove the Power Adapter from the electrical outlet and store in the  
Blowmold case.  
Using the Cordless Screwdriver  
1. Set the Screwdriver handle grip style by pressing on the Grip Button Lock  
and turning the handle for pistol or straight grip.  
Accessory Bit,  
Rocker Switch  
Driver, or Adapter  
(Forward / Reverse)  
Chuck (1)  
Pistol Grip  
Chuck (1)  
Accessory Bit,  
Driver, or Adapter  
Straight Grip  
Grip Button Lock  
2. Insert the desired bit, driver, or adapter into the Chuck (1).  
3. Engage the bit, driver, or adapter over the item being turned.  
4. Press forward on the Rocker Switch for turning clockwise.  
5. Press backward on the Rocker Switch for turning counterclockwise.  
Maintenance  
1. When finished using the Screwdriver, place it in the Blowmold case along  
with all the accessories.  
2. Store in a clean and dry location.  
3. Recharge the batteries once a month whether used or not.  
SKU 91332 Download from Www.SomanuPalsa.cgoem6. All Manuals Search And Download.  
Parts List  
Item #  
1.  
Description  
Chuck  
2.  
3.  
4.  
5.  
6.  
7.  
Screwnail  
Screwnail  
Enclosure (A)  
Screwnail  
Enclosure (right)  
Switch  
8.  
9.  
Limit Block  
Bearing  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
20.  
Limit Box  
Enclosure (B)  
Heat-loss Block  
Gear  
Steering Stem  
Gear  
Gear  
Motor  
Enclosure (left)  
Battery  
Charger Adapter  
NOTE: Some parts are listed and  
shown for illustration purposes only  
and are not available individually as  
replacement parts.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM  
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER  
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO  
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE  
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE  
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY  
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN  
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER  
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE  
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS  
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 91332 Download from Www.SomanuPalsa.cgoem7. All Manuals Search And Download.  
Assembly Drawing  
SKU 91332 Download from Www.SomanuPalsa.cgoem8. All Manuals Search And Download.  

Graco Water Pump 205148 User Manual
Grizzly Appliance Trim Kit G0569 User Manual
Grundig Hot Tub FS 4820 User Manual
Haier Washer HWM 80 000 S User Manual
Harbor Freight Tools Clothes Dryer 67326 User Manual
Honeywell Fan HY108 User Manual
Hotpoint Cooktop G640 User Manual
HP Hewlett Packard Personal Computer A1630n User Manual
Ice O Matic Beverage Dispenser CD20030 CD20530 User Manual
iHome Car Speaker iDM15 User Manual