Frigidaire Dishwasher 740 Series User Manual

Dishwasher

Product Registration Card

Please fill in completely, sign and return promptly!

Use & Care Manual

Safety

740 and 750 Series

Instructions ........................ ²

Features.............................. 3

Normal Operating

Sounds ............................. ^4,6

Operating

Instructions ...................... 4-7

Preparing and

Loading Dishes ............... ^8-9

Dishwasher Dispenser

and Detergents ..............10-11

Factors Affecting

Performance...................... 11

Care and

Cleaning ............................ ¹²

Record All Information For

Future Reference

Solutions to Common

Dishwashing Problems...13-15

Brand:

Purchase Date:

Consumer Services

Warranty & Service .......................... 16,17

Model #:

Serial #:

(see Features page for location)

Questions? 1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Versión en español

Si desea obtener una copia en español de este Manual del

Usuario, sírvase escribir a la dirección que se incluye a

continuación. Solicite la P/N 154386301, Spanish Use & Care

Manual, Electrolux Home Products North America,

P.O. Box 212378, Augusta, GA 30917.

Visit our Web Site at

www.frigidaire.com

READ AND SAVETHESE INSTRUCTIONS

P/N 154395201 (0012)

Dishwasher Features

Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms

against soiled surfaces. Each cycle begins with a pre-drain. Next, the dishwasher fills with water

covering the filter area.Water is then pumped through the filter and spray arms. Soil particles go

down the drain as the water is pumped out and replaced with clean water. The number of water fills

will vary with the cycle being used.

Funnel

pages 8,13

Nozzle and Upper Spray

(some models)

Tub Gasket

Top Rack

page 12

page 8

Serial Label

(located on right

side of tub

Middle Spray Arm

pages 8,9,13

Bottom Rack

page 9

Lower Spray Arm

pages 9,13

Overfill Protector

Glass Trap

page 12

Prewash Detergent

Cup

page 10

Self-Cleaning Filter

page 12

Detergent Dispenser

page 10

Heating

Element

page 12

Rinse Aid

Dispenser

page 11

Vent

pages

4-7,14

Operating Instructions (continued)

Vent

Latch

Getting Started

1. Load dishwasher (See Preparing and

Loading Dishes).

Very Important

Information— Read Before

OperatingYour Dishwasher!

2. Add detergent (See Dishwasher Dispenser

& Detergents).

3. Add rinse aid, if needed (See Rinse Aid).

4. Select desired cycle (See Cycle Chart).

The indicator will show red when selected.

Normal Operating

Sounds

5. Turn dial clockwise to select cycle.

6. Select desired energy OPTIONS (See

Energy Options). The indicator will show

red when selected.

This dishwasher does not sound like most

dishwashers—IT’S QUIETER!

Your dishwasher uses energy efficient motors

for the wash and drain portions of the cycle

you select. Each cycle has a series of water

fills and drains for washing and rinsing

dishes. As each cycle begins, you may–or

may not–hear the drain motor.

7. Run hot water faucet nearest dishwasher

until water is hot.Turn water off.

8. To start, close door to latch.

Status Indicator Light

The next sound you will hear is the splashing

water as it enters the tub.Then the lower arm

rotates and circulates water. This is followed

by a pause and a slightly different sound as

the upper arm sprays water. If you listen

closely, you will hear the change in sound as

the wash action switches from one arm to the

other.

The HEATING DELAY light means the cycle is

being extended to heat water to proper

temperature in the main wash.

PlateWarmer

For warming dishes and serving plates before

serving hot foods:

PLEASE BE ADVISED: If you compare

this dishwasher to previous models, you

may be surprised at what you DON’T hear!

• Load clean plates and dishes to be

warmed.

• Turn dial to PLATE WARMER.

• Select HEAT DRY ON option.

Operating Instructions (continued)

Wash Cycle Selections

Note: Cycle times are approximate and will vary with options selected.

Cycle Chart

Cycle

Description

To Select

Cycle

Water

(approx.)

Time

(approx.) Rinses

Washes/

Pots & For pots, pans,

• Press POTS & PANS pad.

7.2 gal.

6.0 imp. gal.

27.3 liters

85 min.* 2 washes

• Turn dial to POTS & PANS.

• Select HI-TEMP WASH ON option.

• Select other desired OPTIONS.

casseroles, and

dinnerware with

dried-on or baked-

on soils.

4 rinses

Pans

Normal For regularly soiled • Press NORMAL & SHORT pad.

6.0 gal.

5.0 imp. gal.

22.7 liters

78 min.*

2 washes

3 rinses

Wash

dishes and

silverware.

• Turn dial to NORMAL WASH.

• Select desired OPTIONS.

Short

Wash

For lightly soiled or • Press NORMAL & SHORT pad.

4.8 gal.

4.0 imp. gal.

18.2 liters

71 min.* 1 wash

pre-rinsed dishes

and silverware.

• Turn dial to SHORT WASH.

• Select desired OPTIONS.

3 rinses

Rinse/ For rinsing dishes • DO NOT USE detergent.

1.2 gal.

1.0 imp. gal.

4.5 liters

6 min.

1 rinse

Hold

that will be washed • Turn dial to RINSE/HOLD.

later.

* Includes dry time.

Energy Options

Hi-Temp Wash Option

When HI-TEMP WASH ON option is selected,

the dishwasher heats the water in the main

wash to approximately 140°F (60°C). Wash

action will continue but timer will not advance

until proper temperature is reached.The hotter

water provided by this option helps activate

dishwasher detergent to clean food grease and

soil from dishes. HI-TEMP WASH ON option

can be used with any cycle except RINSE/

HOLD.

complete. Some water droplets may remain on

door and tub and in areas where dishes touch

silverware basket or rack.

With either option, you may see water vapor

coming from the vent during the drying portion

of the cycle. The vent is closed during washing

to hold moisture and sound inside and then

opens for drying.

The drying option may be changed at any time

during the cycle and affects only the drying

period.

To turn off option, select HI-TEMP WASH OFF.

Heat Dry Option

The HEAT DRY ON option will provide faster

drying since the heating element is on during

the drying portion of cycle.

HEAT DRY OFF option saves electricity since

the heating element is off during the drying

portion of cycle. To speed the drying process,

open the door slightly after the cycle is

Operating Instructions

Vent

Latch

Getting Started

1. Load dishwasher (See Preparing and

Loading Dishes).

2. Add detergent (See Dishwasher Dispenser

Very Important

& Detergents).

3. Add rinse aid, if needed (See Rinse Aid).

4. Turn dial clockwise to select cycle (See

Cycle Chart) or number of hours for delay

start.

5. Select desired energy OPTIONS (See

Energy Options). The indicator will show

red when selected.

Information— Read Before

OperatingYour Dishwasher!

Normal Operating

Sounds

6. If using DELAY START, go to step number

This dishwasher does not sound like most

dishwashers—IT’S QUIETER!

7. Run hot water faucet nearest dishwasher

until water is hot.Turn water off.

8. To start, close door to latch.

Your dishwasher uses energy efficient motors

for the wash and drain portions of the cycle

you select. Each cycle has a series of water

fills and drains for washing and rinsing

dishes. As each cycle begins, you may–or

may not–hear the drain motor.

Delay Start

Allows you to delay starting the POTS & PANS

cycle up to 6 hours.

• Turn dial to select number of hours.

• Select HI-TEMP WASH ON option and

other desired options.

• Close door to latch. The DELAY START

light will come on.

The next sound you will hear is the splashing

water as it enters the tub.Then the lower arm

rotates and circulates water. This is followed

by a pause and a slightly different sound as

the upper arm sprays water. If you listen

closely, you will hear the change in sound as

the wash action switches from one arm to the

other.

Status Indicator Lights

When DELAY START option is selected, the

Delay Start light will glow as timer counts

down to begin cycle.

PLEASE BE ADVISED: If you compare

this dishwasher to previous models, you

may be surprised at what you DON’T hear!

The HEATING DELAY light means the cycle is

being extended to heat water to proper

temperature in the main wash or final rinse,

based on options selected.

CLEAN light comes on when a cycle is

complete.To turn it off, turn dial slightly until

light goes off.

Operating Instructions (continued)

Wash Cycle Selections

Note: Cycle times are approximate and will vary with options selected.

Cycle Chart

Cycle Description

To Select Cycle

Water

Time Washes/

(approx.) (approx.) Rinses

• Turn dial to POTS & PANS/HEAVY

WASH.

• Select HI-TEMP WASH ON option.

• Select other desired OPTIONS.

Pots & For pots, pans,

7.2 gal.

6.0 imp. gal.

27.3 liters

84 min.* 2 washes

4 rinses

casseroles, and

Pans

dinnerware with dried-

on or baked-on soils.

Heavy For heavily soiled

Wash

• Turn dial to POTS & PANS/HEAVY

WASH.

• Select desired OPTIONS.

7.2 gal.

6.0 imp. gal.

27.3 liters

84 min.*

2 washes

4 rinses

dishes and silverware.

Normal For regularly soiled

Wash

• Turn dial to NORMAL WASH.

6.0 gal.

78 min.* 2 washes

3 rinses

dishes and silverware. • Select desired OPTIONS.

5.0 imp. gal.

22.7 liters

4.8 gal.

4.0 imp. gal.

18.2 liters

1.2 gal.

Short For lightly soiled or

• Turn dial to SHORT WASH.

71 min.* 1 wash

3 rinses

pre-rinsed dishes and • Select desired OPTIONS.

silverware.

Rinse/ For rinsing dishes that • DO NOT USE detergent.

Wash

12min. 1 rinse

• Turn dial to RINSE/HOLD.

• Select SANITIZE OFF and HEAT

DRY OFF.

will be washed later.

Hold

1.0 imp. gal.

4.5 liters

* Includes dry time.

Energy Options

Hi-Temp Wash Option

The sanitize criteria may not be satisfied if

there is an interruption of the cycle, power

failure, or if the incoming water temperature is

below 120°F (49°C).

When HI-TEMP WASH ON option is selected,

the dishwasher heats the water in the main

wash to approximately 140°F (60°C). Wash

action will continue but timer will not advance

until proper temperature is reached.The hotter

water provided by this option helps activate

dishwasher detergent to clean food grease

and soil from dishes. HI-TEMP WASH ON

option can be used with any cycle except

RINSE/HOLD.

Heat Dry Option

HEAT DRY ON option provides faster drying

since the heating element is on during the

drying portion of cycle.

HEAT DRY OFF option saves electricity since

the heating element is off during the drying

portion of cycle.To speed drying process,

open the door slightly after the cycle is

complete. Some water droplets may remain on

door and tub and in areas where dishes touch

silverware basket and rack.

To turn off option, select HI-TEMP WASH OFF.

Sanitize Option

To sanitize your dishes and glassware, select

the SANITIZE ON option.The water

temperature in the final rinse will be raised to

155°F (68°C) and will maintain that

temperature for 9 minutes.This option is

available in Pots & Pans, Heavy, Normal and

Short cycles. The cycle time will be extended

until the proper water temperature is reached.

Washing action will continue during the water

heating delay. For best results, the incoming

water temperature should be at least 120°F

(49°C).

With either option, you may see water vapor

coming from vent during drying portion of

cycle. The vent is closed during washing to

hold moisture and sound inside and then

opens for drying.

The drying option may be changed at any time

during the cycle and affects only the drying

period.

Preparing and Loading Dishes

Loading the Top Rack

Features and appearance of racks and

silverware basket may vary from your model.

Important: Do not cover the funnel when

Dish Preparation

Scrape away large pieces of food, bones, pits,

toothpicks, etc. The continuous filtered wash

system will remove remaining food particles.

Burned-on foods should be loosened before

loading. Empty liquids from glasses and cups.

The top rack is designed for cups, glasses

small plates, saucers and bowls.

Foods such as mustard, mayonnaise, vinegar,

lemon juice and tomato based products may

cause discoloration of stainless steel and

plastics if allowed to sit for a long period of

time. Unless the dishwasher is to be operated

at once, it is best to rinse off these food soils.

Load glasses in top rack. Damage may occur

if placed in bottom rack.

Load plastic items in top rack only. Melting

may occur if placed in bottom rack.

• Load racks so that large items do not

prevent the detergent dispenser from

opening.

Load items with open ends facing down for

better cleaning and draining.

Damage may occur if delicate items touch

each other during dishwasher operation.

• Check manufacturer’s recommendations

before washing items in question.

Long-handled knives and utensils can be

placed in top rack.

• If the dishwasher drains into a food

disposer, be sure disposer is completely

empty before starting dishwasher.

Be sure nothing protrudes through the bottom

of the rack to block rotation of middle spray

arm.

Do not cover funnel

Preparing and Loading Dishes (continued)

Loading the Bottom Rack

Features and appearance of racks and

silverware basket may vary from your model.

Loading the Silverware Basket

Mix spoons, forks and knives to prevent

nesting. Mixing items gives better cleaning and

drying.

Make sure tall items do not block spray arm

rotation.

Place plates and platters so that they do not

touch.

Place bowls, casseroles and sauce pans with

the soiled surface facing down or toward the

center. Tilt slightly for better drainage.

For safety, load sharp knives and forks with

handles up.

Be sure pan handles do not protrude through

the bottom of the rack and block the spray arm

rotation.

Be sure nothing protrudes through bottom of

basket or rack to block the spray arm.

Do not mix silver and stainless to avoid

damaging the silver finish.

Adding a Dish

To add or remove items after wash cycle starts:

• Unlatch door and wait a few seconds until

wash action stops before opening.

• Add the item and wait a few seconds to

allow cold air to slowly expand inside

dishwasher.

• Close door firmly to latch and resume cycle.

Dishwasher Dispenser & Detergents

• Use only fresh automatic dishwashing

detergent. Other types will cause

oversudsing.

Filling the Detergent Dispenser

The detergent dispenser has one covered and

one uncovered cup. Detergent in the

uncovered cup falls into the dishwasher when

the door is closed. The covered cup opens

automatically in the main wash.

• Add detergent just before starting cycle.

• Store detergent in a cool, dry location. Moist

or caked detergent will not dissolve

properly.

Fill to second line

when using standard

dishwashing

Fill both cups

for Pots & Pans,

Heavy and Normal.

detergent.

Fill to first line

when using ultra

or concentrated

detergent.

Fill covered

cup only for

Short Wash.

Cover

How much Detergent to use

Detergent Chart

The amount of detergent to use depends on

the water hardness. Water hardness is

measured in grains per gallon. Using too little

detergent can result in poor cleaning and hard

water filming or spotting. Using too much

detergent in soft water can cause permanent

etching on glassware. Your local water

company, water softener company or county

extension agent can tell you the water

hardness in your area.

Water Hardness

Soft (0-3 grains)

Medium (4-8 grains)

Hard (9+ grains*)

Amount per Cup

2 Teaspoons

5 Teaspoons

10 Teaspoons

(fill level with top)

* 12 grains and higher is extremely hard water.

Detergent alone may not be enough. A water

softener is recommended to improve water

quality and dishwashing performance.

More detergent may be needed if the

phosphorus content is 8.7% or less.

The phosphorus content is shown on the

detergent label.

Factors Affecting

Performance

Dishwasher

Dispenser &

Detergents ^(continued)

Water Pressure

Rinse Aid

The hot water line to dishwasher must provide

water pressure between 20 and 120 psi.

Rinse aid greatly improves drying and

reduces water spots and filming. Water

“sheets” off dishes rather than forming water

droplets that cling and leave spots.

Low water pressure may occur when laundry

or showers are in operation. Wait until water

use is reduced before starting dishwasher.

A dispenser, located next to the detergent cup,

automatically releases a measured amount of

rinse aid during the last rinse. If spotting and

poor drying are problems, increase the amount

of rinse aid dispensed by rotating the dial to a

higher number. The dial is located under the

dispenser cap. The indicator will be dark when

full and will show clear when it is time to refill.

Water Temperature

Hot water is needed for best dishwashing and

drying results. Water entering dishwasher

should be at least 120°F (49°C) to give

satisfactoryresults.

To check water temperature entering

dishwasher:

• Turn on hot water faucet nearest dishwasher

for several minutes to clear cool water from

pipes.

To add liquid rinse aid, turn dispenser cap 1/4

turn counterclockwise and lift out. Pour in rinse

aid until liquid touches the indicated fill level.

Replace cap.

Do not overfill since this can cause oversudsing.

Wipe up any spills with a damp cloth.

• Hold a candy or meat thermometer in

stream of water to check the temperature.

The dispenser holds enough for 35 to 140

washes, depending on setting.

• If temperature is below 120°F (49°C), have

a qualified person raise the hot water heater

thermostatsetting.

Important: Before starting a cycle, run hot

water to clear cool water from pipe.

Indicator

Dispenser Opening

Adjustable setting

Dispenser Cap

Care and Cleaning

Care of Drain Air Gap

If a drain air gap was installed for your built-in

dishwasher, check to make sure it is clean so

the dishwasher will drain properly. A drain air

gap is usually mounted on countertop and can

be inspected by removing the cover. This is not

part of your dishwasher and is not covered by

warranty.

Burn Hazard

Allow heating element to cool

before cleaning the interior.

Failure to do so can result in

burns.

Outside—Occasionally wipe with a mild

nonabrasive detergent and water. Rinse and

dry.

Property Damage Hazard

Inside—The inside of the dishwasher is self-

cleaning with normal use. If needed, clean

around the tub gasket area with a damp cloth.

Freezing temperatures may cause water

lines to rupture. Be sure all supply lines to

and circulating lines within dishwasher are

protected.

The filter is self-cleaning. A glass trap located

in the center of the filter is designed to collect

pieces of broken glass, straws, bones and pits.

To remove items in glass trap, grasp handle, lift

out, empty and replace.

Failure to do so could result in property

damage.

Winterizing

A dishwasher left in an unheated place should

be protected from freezing. Have a qualified

person do the following:

To Disconnect Service:

1. Turn off electrical power to the dishwasher

at the supply source by removing fuses or

tripping circuit breaker.

2. Shut off water supply.

Note: Hard water may cause lime deposit

buildup on the interior of the dishwasher. For

cleaning instructions see “Removing Spots

and Film” section.

3. Place a pan under the inlet valve.

Disconnect water line from inlet valve and

drain into pan.

4. Disconnect drain line from pump and drain

water into pan.

Overfill Protector—keeps dishwasher

from overfilling and is located in the left front

corner of the tub.

• Clean occasionally with household cleaner

containing vinegar or

To Restore Service:

1. Reconnect the water, drain, and electrical

power supply.

2. Turn on water and electrical power supply.

bleach to dissolve any

buildup.

3. Fill both detergent cups and run

dishwasher through a NORMAL cycle.

• Overfill Protector should

move up and down

freely about one inch. If

it does not move, lift and

clean underneath.

4. Check connections to make sure they do

not leak.

Note: See Installation Instructions for more

details.

Solutions to Common Dishwashing Problems

Before calling for service, review this list. It

Glassware/Flatware Spotted or

Cloudy

• Check water hardness. For extremely hard

water, it may be necessary to install a water

softener.(See Detergent Chart.)

may save you both time and expense.This

list includes common experiences that are

not the result of defective workmanship or

material in your dishwasher.

Food Soils Left on Dishes

• Choose another cycle for longer washing

time.

• Water temperature may be low. Avoid

extremely low or high temperatures. (See

Factors Affecting Performance.)

• Check rack loading section for proper

loading—avoid nesting items.

• Avoid overloading and improper loading.

(See Preparing and Loading Dishes.)

• Home water pressure may be too low—

should be 20 to 120 pounds per square inch

(psi).

• Use fresh detergent. Old detergent is

ineffective.

• Make sure rinse aid dispenser is filled.

• Check incoming water temperature. It

should be at least 120°F (49°C). (See

Factors Affecting Performance.)

• Check to see that proper amount of

detergent is being used for cycle selected.

Also, check phosphate level. (See Detergent

Dispenser.)

• Select HI-TEMP WASH option.

• Check water hardness. For extremely hard

water, it may be necessary to install a water

softener.(See Detergent Chart.)

• Home water pressure may be too low—it

should be 20 to 120 pounds per square inch

(psi).

• Use fresh detergent.

Dishware Chipped

• Load with care and do not overload. (See

Preparing and Loading dishes.)

• Check to make sure funnel in top rack is not

blocked.

• Make sure items are not blocking the spray

arms, preventing them from rotating.

• Place delicate items in top rack.

• Place glasses securely against pins and not

over pins.

Dishes not Dry

• Select Heat Dry option.

• Load items so they are secure and don’t jar

loose when moving racks in and out. Move

racks in and out slowly.

• Make sure the rinse aid dispenser is filled.

• Increase the amount of rinse aid. (See Rinse

Aid.)

• Make sure tall glasses and stemware will

clear top of tub when rack is pushed in.

• Check the incoming water temperature. Be

sure it is at least 120°F (49°C).

• Fine antique china and crystal should be

hand-washed.

• Check for proper loading—avoid nesting

items.

• Plastic items may need to be towel dried.

• Cups with a concave bottom will collect

water.

Solutions to Common Dishwashing Problems

(continued)

Dishware Stained or Discolored

Dishwasher Leaks

• Tea and coffee can stain cups. Remove the

stains by hand washing in a solution of 1/2

cup (120 ml) bleach and one quart (1 L) of

warm water. Rinse thoroughly.

• Use only fresh detergent designed for

automatic dishwashers. Measure detergent

carefully.Try a different brand.

• Spilled rinse aid can cause foam and lead to

overflowing. Wipe up any spills with a damp

cloth.

• Iron deposits in water can cause a yellow or

brown film. A special filter installed in the

water supply line will correct this problem.

(See Removing Spots and Film.)

• Check to see that dishwasher is level. (See

Installation Instructions.)

• Aluminum utensils can leave gray/black

marks when they rub against other items.

Load properly.

Normal Sounds You Will Hear

• Normal sounds include water fill, water

circulation and motor sounds.

• Certain high acid foods can cause

discoloration of stainless steel and plastics

if allowed to sit for a long period. Use the

Rinse/Hold cycle or rinse by hand if not

operating dishwasher at once.

• There is a noticeable change in sound when

the wash action switches between the lower

and middle spray arm. This is normal since

each spray arm has its own sound.

• Mixing stainless steel and silver utensils in

silverware basket can cause pitting of the

stainless steel blades. Avoid mixing

stainless steel and silver.

• It is normal for dishwasher to pause (no

sound) when the wash action is switching

between the lower and middle spray arms.

Water in Bottom of Tub

Etching

• Water left in bottom of tub after cycle is

complete is not normal. If water remains in

the bottom of the tub, dishwasher may not be

draining properly. (See Dishwasher Does

Not Drain Properly.)

• Using too much detergent in soft or softened

water causes this film that cannot be

removed.

• Adjust the amount of detergent based on the

water hardness. (Check Detergent Chart.)

Vapor at Vent

• Lower the water temperature.

• Use the Heat Dry Off option.

• Water vapor escapes from the vent when the

dishwasher goes into the drying part of

cycle. This is normal.

Detergent Left in Cups

• Detergent may be old. Discard and use

freshdetergent.

Dishwasher Won’t Run

• Check to see if circuit breaker is tripped or if

a fuse is blown.

• Be sure water action can reach the

dispenser.

• Make sure water supply is turned on.

• Check to see if cycle has been completed.

• Check to see if cycle is set correctly. (See

OperatingInstructions.)

• Make sure items do not prevent the

detergent dispenser from opening.

• Is dishwasher set for delay start option?

• Make sure door is closed and latched.

Solutions to Common Dishwashing Problems

(continued)

Stains on Tub Interior

Dishwasher Does Not Drain

Properly

• If unit is hooked up to a food waste

• Washing large amounts of dishware with

tomato based soil can cause a pink/orange

appearance. This will not affect

disposer, make sure the disposer is empty.

performance and will gradually fade over

time. Pre-rinsing will reduce the chance of

staining. Using HEAT DRY OFF option will

lessen staining.

• Check to see if the knockout plug has been

removed from inside the food waste

disposer inlet.

• Check to see if drain hose is kinked.

Removing Spots and Film

• Make sure cycle is complete, not in a

pause.

Hard water can cause lime deposit buildup on

the interior of the dishwasher. Dishes and

glasses may also get spots and film for a

number of reasons. (See Glassware/Flatware

Spotted or Cloudy section.) To remove buildup,

spots and film, clean using the following

instructions:

Cycle Takes a Long Time

• Is cycle in a water heating delay?

• Has the delay start option been selected?

• Has the sanitize option been selected?

1. Load clean dishes and glasses in normal

manner. Do not load any metal utensils or

silverware.

Dishwasher Won’t Fill

• Is water supply turned on?

• Check your home circuit breaker or fuse

box.

• Check inlet hose for a kink.

2. Do not add detergent.

3. Select the POTS & PANS cycle. Close and

latchdoor.

• Does overfill protector move up and down

freely? (See Overfill Protector section.)

4. Allow dishwasher to run for 25 minutes to

reach the main wash portion of cycle.

5. Unlatch and open door and pour 2 cups of

white vinegar into the bottom of dishwasher.

Dishwasher Has an Odor

• Soiled dishes left in dishwasher too long

can create an odor. Rinse dishes if not

running dishwasher at once.

6. Close and latch door and allow cycle to

finish.

Note: If these conditions persist, a home water

softener should be considered.

• There will be a “new” smell when first

installed. This is normal.

• Check to see if unit is draining properly.

(See Dishwasher Does Not Drain Properly.)

To customize your dishwasher to match your cabinets:

• You will need a trim kit.

• See Step 10 of Installation Instructions that came with your dishwasher for more

information.

GIBSON DISHWASHER PLATINUM ADVANTAGE WARRANTY

(USA Only)

Your dishwasher is protected by this warranty

WARRANTY

PERIOD

THROUGHOURAUTHORIZEDSERVICERS,

WEWILL:

THECONSUMERWILLBE

RESPONSIBLEFOR:

Pay all costs for repairing or replacing any parts of this

appliance which prove to be defective in materials or

workmanship.

Costs of service calls that are listed under

NORMALRESPONSIBILITIESOFTHE

CONSUMER.*

FULLTWO-YEAR

WARRANTY

Two years from

original purchase date.

Replace any tub or door liner (parts only) that fails to contain

water due to a defect in materials or workmanship.

Third through tenth years

fromoriginalpurchasedate.

Door seals; any costs for pickup and delivery of

the product required because of service; and all

costs for labor and transportation.

LIMITED3RD-10TH

YEARWARRANTY

Time periods listed above.

All of the provisions of the full warranties above and the Costs of the technician's travel to the home and

LIMITEDWARRANTY

(Applicabletothe

StateofAlaska)

exclusions listed below apply.

any costs for pick up and delivery of the appliance

required because of service.

Your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries, Inc. We authorize no person

to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us

or an authorized Electrolux Home Products North America servicer.

*NORMAL

RESPONSIBILITIES

OF THE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the items

listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in

accordance with all local plumbing, electrical and/or gas codes.

CONSUMER

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose

connections or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which

are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

EXCLUSIONS

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or

exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary

household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by persons other than Electrolux Home Products North America or its

authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons other

than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty

period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This

written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under

this warranty must be obtained by contacting Electrolux Home Products North America:

IF YOU NEED

SERVICE

This warranty only applies in the 50 states of the U.S.A. and Puerto Rico. Product features or specifications as described or illustrated are

subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidated

Industries, Inc.

05-G-DW-01(Rev. 01/2001)

USA 800•944•9044

Electrolux Home Products North America

P.O. Box 212378

Augusta, GA 30917

Warranty Information

(Canada Only)

DISHWASHER WARRANTY Your dishwasher is protected by this warranty

THROUGHOURAUTHORIZEDSERVICERS,

WEWILL:

THECONSUMERWILLBE

RESPONSIBLEFOR:

WARRANTY

PERIOD

Payallcostsforrepairingorreplacinganypartsofthisappliance Costs of service calls that are listed under

FULLONE-YEAR

WARRANTY

One year from original

purchase date.

which prove to be defective in materials or workmanship.

NORMALRESPONSIBILITIESOFTHE

CONSUMER.*

Two years from

original purchase date.

Replace any parts in the Water Distribution System which fail Associated inlet and drain plumbing parts. Costs

EXTENDEDLIMITED

2NDYEAR

WARRANTY

because of a manufacturing defect. This includes the motor,

pump,lowerwasharmandsoftorhardfooddisposeronallmodels,

plus the wash tower, upper spray arms with associated supply

tube, and filter assembly on models including these features.

Associatedinletanddrainplumbingpartsarenotcoveredbythis

warranty.

for pickup and delivery of the product required

because of service; and all costs for labor and

transportation.

Second through fifth years

fromoriginalpurchasedate.

EXTENDEDLIMITED

2ND-5THYEAR

WARRANTY

(Electronic Controls, Nylon Racks and TufRacks) For models Costsforpickupanddeliveryoftheproductrequired

withelectroniccontrols, replaceanyelectroniccontrolthatfails because of service; and all costs for labor and

due to a manufacturing defect. For models with nylon-coated transportation.

racks or TufRacks, replace any original upper or lower nylon-

coatedrackorTufRackthatpeelsorrustsduetoamanufacturing

defect.

EXTENDEDLIMITED

2ND-10THYEAR

Provideareplacementtubordoorlineriftheoriginaltubordoor

liner fails to contain water because of a manufacturing defect.

Secondthroughtenthyears

fromoriginalpurchasedate.

Doorseals;anycostsforpickupanddeliveryofthe

product required because of service; and all costs

for labor and transportation.

LIMITEDWARRANTY

(Applicabletothe

StateofAlaska)

Time periods listed above.

All of the provisions of the full warranties above and the

exclusions listed below apply.

Costsofthetechnician'straveltothehomeandany

costs for pick up and delivery of the appliance

required because of service.

In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries, Inc. We authorize

no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed

by us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada Inc.