EP585H
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO OPERATING LLC warrants this product to be free from defects in material
and workmanship for a period of one (1) year from the date of purchase when utilized for
normal household use.
If your appliance fails to operate properly while in use under normal household
conditions within the warranty period, return the complete appliance and accessories,
freight prepaid to EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh,
N.Y. 12901. If the appliance is found to be defective in material or workmanship, EURO-
PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and
$12.95 to cover the cost of return shipping and handling must be included.*
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts
and does not apply to any unit that has been tampered with or used for commercial
purposes. This limited warranty does not cover damage caused by misuse, abuse,
negligent handling or damage due to faulty packaging or mishandling in transit.
This warranty is extended to the original purchaser of the unit and excludes all other
legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if
any, is limited to the specific obligations expressly assumed by it under the terms of the
limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or
CONVERTIBLE
HAND/STAND MIXER
OWNER’S MANUAL
Model EP585H
127V., 60Hz., 325 Watts
consequential damages of any nature whatsoever. Some states do not permit the
exclusion or limitation of incidental or consequential damages, so the above may not
apply to you.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include
proof of purchase date and to attach tag to item before packing with your name,
complete address and phone number with a note giving purchase information,
model number and what you believe is the problem with item. We recommend you
insure the package (as damage in shipping is not covered by your warranty). Mark
the outside of your package “ATTENTION CUSTOMER SERVICE”. We are
constantly striving to improve our products, therefore the specifications contained
herein are subject to change without notice.
---------------------------------------------------------------------------------------------------------------------------
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase.
The registration will enable us to contact you in the unlikely event of a product safety
notification. By returning this card you acknowledge to have read and understood the
instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO EURO-PRO OPERATING LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901
EP585H
______________________________________________________________________
Appliance model
______________________________________________________________________
Date purchased
Name of store
______________________________________________________________________
Owner’s name
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
_
_____________________________________________________________________
Address
City
State
Zip Code
7
Tel.: 1 (800) 798-7398
Printed in China
GETTING TO KNOW YOUR CONVERTIBLE
HAND/STAND MIXER
OPERATING INSTRUCTIONS
Fitting the Bowl onto the
Using the Convertible Hand/Stand
Mixer
Turntable of the Stand
Warning: To avoid injury when
assembling the hand mixer to the
stand, always set the speed selector on
“0” and unplug the appliance.
Warning: To avoid injury when
assembling the hand mixer to the
stand, always set the speed selector on
“0” and unplug the appliance.
1. Place the base of the mixing bowl
onto the turntable of the stand. To
fully lock the mixing bowl in place,
press down and turn the mixing bowl
in a clockwise direction until you hear
it click into place. (Fig. 9)
1. Before plugging the hand/stand mixer
into the electrical outlet, assemble the
unit with the desired accessories.
2. Set the speed selector switch to the
“HI” or “LO” position.
3. Select the speed that you desire.
MIXING GUIDE
MIXING
TASK
RECOMMENDED
SPEED(S)
Folding &
Blending
“LO” 1 & 2
“LO” 3 & 4
Fig. 9
Light Mixing
Creaming &
Beating
“HI” 6 - 8 or “LO” 5
2. To remove the mixing bowl from the
stand, press down and turn the mixing
bowl counter clockwise. The mixing
bowl can now be detached from the
turntable and lifted away. (Fig. 10)
Whipping &
Aerating
“HI” 9 & 10 or
BURST
12
14
13
4. Select the bowl speed – “LO” or “HI”
depending on how fast you want the
bowl to turn. Use the “LO” bowl
speed for mixing speed 1-5. Use the
“HI” bowl speed for mixing speed
6-10. If you do not wish the bowl to
turn, leave the bowl speed in the
“OFF” position.
15
Note:
•
Fig. 10
Always select the speed setting
before the mixing bowl speed to
prevent ingredients from being flicked
out of the mixing bowl.
Always start mixing at slow speeds
and increase the speed gradually to
prevent the ingredients splashing out
of the bowl.
1. Hi-Lo Speed Selector
2. Speed Control
3. Burst of Speed Button
4. Beater Eject Button
5. Beaters
6. Stainless Steel Bowl
7. Tilt Button
8. Hand Mixer Release Button
9. Bowl Speed Control Dial
10. Hand Mixer
11. Base Stand
12. Dough Hooks
13. Plastic Bowl
14. Bowl Lid
Note: It is easier to fit the mixing bowl to
the turntable when the hand mixer is not
attached to the pivot support.
•
15. Spatula
Technical Specifications
Voltage:
Power:
Bowl Capacity:
127V., 60Hz.
325Watts
3.5 Qts.
2
5
Read all the sections of this booklet and follow all the instructions carefully.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Assembling the Hand Mixer to
the Stand
Warning: To avoid injury when
assembling the hand mixer to the
stand, always set the speed selector on
“0” and unplug the appliance.
3. While the hand mixer is still in the
raised position, insert either the
beaters or the dough hooks.
4. To lower the hand mixer, press and
hold the tilt button with one hand
while holding the hand mixer with the
other hand and slowly lower the hand
mixer down. (Fig. 6)
Attaching the Dough Hooks to
the Hand Mixer
Warning: To avoid injury when
inserting or removing beaters or
1. Ensure that the hand mixer is not
plugged in to an electrical outlet
and that the speed control switch
is on the “0” (off) position.
2. The dough hooks have a set
method of fitting into the hand
mixer because they are not
dough hooks, always set the speed
selector on “0” and unplug the appliance.
1. Before using your Bravetti
Convertible Hand/Stand Mixer for
the first time, wash the beaters,
dough hooks, bowls and spatula in
warm, sudsy water. Rinse and dry
thoroughly. Use a damp cloth to wash
over the mixer base and the hand
mixer. Dry with a soft cloth.
1. Press the tilt button, located on the
top of the support pivot . While the
button is depressed, ease the support
pivot back. (Fig. 4)
Press the
tilt button
and tilt the
hand
mixer
down
identical. One has a grommet and
the other does not. (Fig. 2)
Tilt Button
NEVER immerse the base stand or
the hand mixer in water or any other
liquids.
Support
Pivot
Grommet
2. Before assembling your Convertible
Hand/Stand Mixer, make sure that the
power cord is unplugged from the
electrical outlet and that both the
speed control and the base speed
control dial are in the “OFF” position.
Fig. 6
Fig. 2
Fig. 4
The support pivot will lock into this
raised position until it is released by
pressing the tilt button again.
5. To remove the hand mixer from the
pivot support, first raise the mixer by
pressing the tilt button and raise the
mixer up. (Fig. 7) the mixer will lock
into the raised position.
6. Then press the mixer release button
which is located on the under side of
the pivot support with one hand and
with the other lift the hand mixer by
the handle upwards and away from
the support pivot. (Fig. 8)
3. Looking at the under side of the
hand mixer, you will see that one
of the sockets has a red dot over
it. (Fig. 3) Insert the dough hook
with the grommet into this socket.
Attaching the Beaters to the
Hand Mixer
1. Ensure that the hand mixer is not
plugged in to an electrical outlet
and that the speed control switch
is on the “0” (off) position.
2. To connect the hand mixer to the
support pivot, locate the two retaining
prongs on the support pivot into the
two rectangular holes in the heel of
the hand mixer. (Fig. 5) When the
hand mixer is seated on the support
pivot, press down on the hand mixer
to click it into place and lock the hand
mixer and the support pivot together.
2. Insert the beaters into the sockets
on the under side of the hand
mixer and twist counter clockwise
until the beater is firmly fitted into
the socket.
3. To release the beaters from the
unit, press on the beater eject
button on the front of the unit and
they will pop out. (Fig. 1)
Grommet
Press the
tilt button
and tilt the
hand
mixer up
Rectangular
holes
Fig. 3
Press
eject
4. Then insert the other dough hook
into the other socket. Push both
dough hooks in until you hear a
click confirming that they are
securely in place.
5. To release the dough hooks from
the unit, press on the beater eject
button on the front of the unit and
they will pop out. (Fig. 1)
Note: Ensure that the beaters or
dough hooks are fully inserted into
the correct sockets or your mixing
results may be affected.
Fig. 7
button
Retaining
prongs
Support
pivot
Fig. 5
Note: Ensure that the two retaining
prongs on the support pivot are fully
connected into the hand mixer.
Hand
mixer
release
button
Fig. 1
Fig. 8
3
4
|