Porter Cable Power Screwdriver 4630 User Manual

ESPAÑOL: PÁGINA 15  
FRANÇAISE : PAGE 27  
Instruction  
manual  
Double Insulated  
Portable Electric  
Screwdrivers  
MODELS 4630 and 4634  
Depth Sensing Drywall and Deck Drivers  
MODEL 4640  
Depth Sensing Fastener Driver  
IMPORTANT  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. ______________________________________  
Type ___________________________________________  
Serial No._______________________________________  
Copyright © 2005 Porter-Cable Corporation  
Part No. 896132 - 03-10-05  
 
SAFETY GUIDELINES - DEFINITIONS  
It is important for you to read and understand this manual. The  
information it contains relates to protecting YOUR SAFETY and  
PREVENTING PROBLEMS. The symbols below are used to help  
you recognize this information.  
indicates an imminently hazardous situation which, if not  
avoided, will result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,could result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,may result in minor or moderate injury.  
used without the safety alert symbol indicates potentially  
hazardous situation which, if not avoided, may result in  
property damage.  
CALIFORNIA PROPOSITION 65  
Some dust created by power sanding, sawing, grinding, drilling,  
and other construction activities contains chemicals known (to the  
State of California) to cause cancer, birth defects or other reproductive harm. Some  
examples of these chemicals are:  
lead from lead-based paints  
crystalline silica from bricks and cement and other masonry products  
arsenic and chromium from chemically-treated lumber  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, always wear  
NIOSH/OSHA approved, properly fitting face mask or respirator when using  
such tools.  
3
 
GENERAL SAFETY RULES  
Read all instructions. Failure to follow all  
instructions listed below may result in electric shock, fire and/or  
serious injury. The term "power tool" in all of the warnings listed  
below refers to your mains-operated (corded) power tool or  
battery-operated (cordless) power tool.  
SAVE THESE INSTRUCTIONS  
1) Work area safety  
a) Keep work area clean and well lit. Cluttered or dark areas invite  
accidents.  
b) Do not operate power tools in explosive atmospheres, such as in the  
presence of flammable liquids, gases or dust. Power tools create  
sparks which may ignite the dust or fumes.  
c) Keep children and bystanders away while operating a power tool.  
Distractions can cause you to lose control.  
2) Electrical safety  
a) Power tool plugs must match the outlet. Never modify the plug in any  
way. Do not use any adapter plugs with earthed (grounded) power  
tools. Unmodified plugs and matching outlets will reduce risk of electric  
shock.  
b) Avoid body contact with earthed or grounded surfaces such as  
pipes, radiators, ranges and refrigerators. There is an increased risk of  
electric shock if your body is earthed or grounded.  
c) Do not expose power tools to rain or wet conditions. Water entering a  
power tool will increase the risk of electric shock.  
d) Do not abuse the cord. Never use the cord for carrying, pulling or  
unplugging the power tool. Keep cord away from heat, oil, sharp  
edges or moving parts. Damaged or entangled cords increase the risk  
of electric shock.  
e) When operating a power tool outdoors, use an extension cord  
suitable for outdoor use. Use of a cord suitable for outdoor use reduces  
the risk of electric shock.  
3) Personal safety  
a) Stay alert, watch what you are doing and use common sense when  
operating a power tool. Do not use a power tool while you are tired  
or under the influence of drugs, alcohol or medication. A moment of  
inattention while operating power tools may result in serious personal  
injury.  
b) Use safety equipment. Always wear eye protection. Safety equipment  
such as dust mask, non-skid safety shoes, hard hat, or hearing  
protection used for appropriate conditions will reduce personal injuries.  
c) Avoid accidental starting. Ensure the switch is in the off-position  
before plugging in. Carrying power tools with your finger on the switch  
or plugging in power tools that have the switch on invites accidents.  
4
 
continued  
GENERAL SAFETY RULES  
d) Remove any adjusting key or wrench before turning the power tool  
on. A wrench or a key left attached to a rotating part of the power tool  
may result in personal injury.  
e) Do not overreach. Keep proper footing and balance at all times. This  
enables better control of the power tool in unexpected situations.  
f) Dress properly. Do not wear loose clothing or jewelry. Keep your  
hair, clothing and gloves away from moving parts. Loose clothes,  
jewelry or long hair can be caught in moving parts.  
g) If devices are provided for the connection of dust extraction and  
collection facilities, ensure these are connected and properly used.  
Use of these devices can reduce dust-related hazards.  
4) Power tool use and care  
a) Do not force the power tool. Use the correct power tool for your  
application. The correct power tool will do the job better and safer at the  
rate for which it was designed.  
b) Do not use the power tool if the switch does not turn it on and off.  
Any power tool that cannot be controlled with the switch is dangerous  
and must be repaired.  
c) Disconnect the plug from the power source before making any  
adjustments, changing accessories, or storing power tools. Such  
preventive safety measures reduce the risk of starting the power tool  
accidentally.  
d) Store idle power tools out of the reach of children and do not allow  
persons unfamiliar with the power tool or these instructions to  
operate the power tool. Power tools are dangerous in the hands of  
untrained users.  
e) Maintain power tools. Check for misalignment or binding of moving  
parts, breakage of parts and any other condition that may affect the  
power tools operation. If damaged, have the power tool repaired  
before use. Many accidents are caused by poorly maintained power  
tools.  
f) Keep cutting tools sharp and clean. Properly maintained cutting tools  
with sharp cutting edges are less likely to bind and are easier to control.  
g) Use the power tool, accessories and tool bits etc., in accordance  
with these instructions and in the manner intended for the  
particular type of power tool, taking into account the working  
conditions and the work to be performed. Use of the power tool for  
operations different from those intended could result in a hazardous  
situation.  
5) Service  
a) Have your power tool serviced by a qualified repair person using only  
identical replacement parts. This will ensure that the safety of the  
power tool is maintained.  
5
 
ADDITIONAL SPECIFIC SAFETY RULES  
1. Hold power tools by insulated gripping surfaces when performing  
an operation where the cutting tool may contact hidden wiring or its  
own cord. Contact with a "live" wire will make exposed metal parts of  
the tool "live" and shock the operator.  
2. Verify the direction of rotation before starting the tool. Never  
attempt to change direction of rotation while switch is “ON”. To do  
so, may damage interlock feature built into switch. Be sure switch is  
“OFF” and motor has completely stopped before changing direction of  
rotation.  
3. Wear eye and hearing protection. Always use safety glasses. Everyday  
eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.  
Eye protection equipment should comply with ANSI Z87.1 standards.  
Hearing equipment should comply with ANSI S3.19 standards.  
4.  
Use of this tool can generate and disburse dust or other  
airborne particles, including wood dust, crystalline silica dust and  
asbestos dust. Direct particles away from face and body. Always operate  
tool in well ventilated area and provide for proper dust removal. Use dust  
collection system wherever possible. Exposure to the dust may cause  
serious and permanent respiratory or other injury, including silicosis (a  
serious lung disease), cancer, and death. Avoid breathing the dust, and  
avoid prolonged contact with dust. Allowing dust to get into your mouth or  
eyes, or lay on your skin may promote absorption of harmful material.  
Always use properly fitting NIOSH/OSHA approved respiratory protection  
appropriate for the dust exposure, and wash exposed areas with soap and  
water.  
SAVE THESE INSTRUCTIONS!  
SYMBOL  
DEFINITION  
........................ volts  
V
A
........................ amperes  
........................ hertz  
........................ watts  
........................ kilowatts  
........................ farads  
........................ microfarads  
........................ litres  
Hz  
W
kW  
F
µF  
l
g
........................ grams  
........................ kilograms  
........................ bars  
........................ pascals  
........................ hours  
........................ minutes  
........................ seconds  
........................ no-load speed  
kg  
bar  
Pa  
h
min  
s
n0  
…/min or …min 1 ......... Revolutions or reciprocations per minute  
-
or d.c. ................ direct current  
or a.c. ................ alternating current  
6
 
2
........................ two-phase alternating current  
2N  
3
........................ two-phase alternating current with neutral  
........................ three-phase alternating current  
3N  
........................ three-phase alternating current with neutral  
........................ rated current of the appropriate fuse-link in amperes  
........................ time-lag miniature fuse-link where X is the symbol  
for the time/current characteristic, as given in IEC 60127  
........................ protective earth  
........................ class II tool  
........................ IP symbol  
IPXX  
SAVE THESE INSTRUCTIONS!  
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60  
cycle A.C. current and voltage within plus or minus 5 percent of that shown on  
the specification plate on the tool. Several models, however, are designed for  
A.C. current only. Refer to the specification plate on your tool for proper voltage  
and current rating.  
Do not operate your tool on a current on which the  
voltage is not within correct limits. Do not operate tools rated A.C.  
only on D.C. current. To do so may seriously damage the tool.  
EXTENSION CORD SELECTION  
If an extension cord is used, make sure the conductor size is large enough to  
prevent excessive voltage drop which will cause loss of power and possible  
motor damage. A table of recommended extension cord sizes will be found in  
this section. This table is based on limiting line voltage drop to 5 volts (10 volts  
for 230 volts) at 150% of rated amperes.  
If an extension cord is to be used outdoors, it must be marked with the suffix W-  
A or W following the cord type designation. For example – SJTW-A to indicate it  
is acceptable for outdoor use.  
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS  
Length of Cord in Feet  
115V  
230V  
25 Ft.  
50 Ft.  
50 Ft.  
100 Ft. 150 Ft. 200 Ft.  
250 Ft. 300 Ft.  
500 Ft. 600 Ft.  
400 Ft. 500 Ft.  
800 Ft. 1000 Ft.  
100 Ft. 200 Ft. 300 Ft. 400 Ft.  
0-2  
2-3  
18  
18  
18  
18  
18  
18  
18  
16  
16  
16  
14  
14  
18  
18  
18  
18  
16  
16  
14  
14  
12  
12  
12  
12  
18  
16  
16  
14  
14  
12  
12  
10  
10  
10  
8
16  
14  
14  
12  
12  
10  
10  
8
16  
14  
12  
12  
10  
10  
8
14  
12  
12  
10  
10  
8
14  
12  
10  
10  
8
12  
10  
10  
8
12  
10  
8
3-4  
4-5  
8
5-6  
8
6
6-8  
6
6
6
8-10  
10-12  
12-14  
14-16  
16-18  
18-20  
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
7
 
CARTON CONTENTS  
Carton contents include the screwdriver, an instruction manual, and a parts list.  
FUNCTIONAL DESCRIPTION  
FOREWORD  
Porter-Cable screwdrivers are designed to install or remove various sizes and  
types of fasteners.  
ASSEMBLY  
NOTE: This tool is shipped completely assembled. No assembly time or tools  
are required.  
OPERATION  
TO START AND STOP THE TOOL  
Make sure that the switch is off before connecting the  
tool to the power source.  
Check to see that the switch is “OFF”. Make sure that the power circuit voltage  
is the same as that shown on the specification plate of the tool. Connect the drill  
to the power circuit.  
1. Squeeze the trigger switch (A)  
Fig. 1 to start the motor. Release  
the trigger to stop the motor.  
B
C
2. A lock button (B) Fig. 1 is pro-  
vided to keep the motor running  
without holding the trigger switch  
“ON”. TO LOCK the trigger  
switch “ON”, squeeze the trigger  
as far as it will go, push in lock  
button and release trigger. TO  
UNLOCK the lock button,  
squeeze the trigger and release,  
leaving the lock button free to  
spring out.  
Fig. 1  
A
NOTE: The lock button can be engaged only when the tool is running at  
maximum speed.  
Never use the lock button when the tool may have to be  
stopped suddenly.  
3. These tools will operate in either the forward direction (clockwise rotation)  
for drilling holes, or the reverse direction (counter-clockwise rotation) for  
releasing jammed drill bits. For counter-clockwise rotation, stop the motor  
by releasing the trigger switch and push the reversing switch (C) Fig. 1  
toward the right side of the drill, or in the opposite direction for clockwise  
rotation.  
 
8
Never attempt to change direction of rotation while the switch  
is “ON”. To do so, may damage interlock feature built into  
switch. Be sure that the switch is “OFF” and the motor has  
completely stopped before changing the direction of rotation.  
4. VARIABLE SPEED – As the trigger switch is squeezed, the tool speed  
increases.  
TO CHANGE HEX NUTSETTER – MODEL 4640  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Pull the Depth Stop Assembly (A) Fig. 2 from the clutch housing (B).  
2. Pull the nutsetter (C) Fig. 3 straight out. If it is difficult to remove, grip it with  
pliers and pull.  
3. Push the nutsetter into the screwdriver spindle until the ball in the spindle  
snaps into the groove in the nutsetter shank.  
4. Replace the depth stop assembly and adjust for depth of drive (see  
ADJUST DEPTH STOP, MODEL 4640”).  
C
A
B
Fig. 3  
Fig. 2  
ADJUST DEPTH STOP – MODEL 4640  
1. Turn the adjusting collar (A) Fig. 2 until the end of the depth stop is flush with  
the end of the nutsetter. Do not push the nutsetter in. This will engage the  
internal drive.  
2. Drive a test fastener into a piece of scrap material identical to the workpiece.  
Examine the results of the drive and make any necessary depth stop  
adjustments.  
a) To increase the depth of drive, repeat STEP 1 and turn the adjusting  
collar so that the end of the nutsetter extends beyond the end of the  
depth stop.  
b) To decrease the depth of drive, repeat STEP 1 and turn the adjusting  
collar so that the end of the depth stop extends beyond the end of the  
nutsetter.  
Each click of the adjusting collar results in .007" change in the depth of drive.  
3. Repeat STEPS 1 and 2 until the desired result is obtained.  
9
 
CHANGE BIT HOLDER – MODELS 4630, 4634  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Pull the Depth Stop Assembly (A)  
Fig. 4 from the clutch housing.  
2. Pull the bit holder (C) Fig. 4 out. If  
it is difficult to remove, grip it with  
pliers and pull.  
B
NOTE: You can remove the bit (B) Fig.  
4 from the bit holder by pulling it  
straight out.  
A
3. Push the new bit holder into the  
spindle and snap it into place.  
4. Replace the Depth Stop Assem-  
bly and adjust the depth stop  
(see “ADJUST DEPTH STOP,  
MODELS 4630 AND 4634”).  
C
Fig. 4  
ADJUST DEPTH STOP – MODELS 4630 AND 4634  
1. Turn the adjusting collar until the end of the bit extends 3/32" beyond the  
end of the depth stop. Do not push the bit holder in. This will engage the  
internal drive.  
2. Drive a test fastener in the same material as your workpiece. Examine the  
results and make any additional depth stop adjustments:  
a) To increase the depth of drive, repeat STEP 1 and turn the adjusting  
collar so that the end of the bit extends further than the end of the  
depth stop.  
b) To decrease depth of drive, repeat STEP 1 and turn the adjusting collar  
so that the end of the bit is closer to the end of depth stop. Each click  
of the adjusting collar results in a .007" change in the depth of drive.  
3. Repeat STEPS 1 and 2 until the desired result is obtained.  
DRIVING DRYWALL SCREWS – MODELS 4630, 4634  
NOTE: Maximum size screw for use with this tool is #12 Wood Screw.  
1. Install a drywall bit and bit holder in the screwdriver.  
2. Set the screwdriver for the correct rotation.  
3. Start the screwdriver and place a drywall screw on the bit.  
Do not exert pressure on the screw while performing this  
operation.  
4. Place the end of the screw in the desired location and remove your fingers.  
5. Apply forward pressure to the drive screw until the depth stop rests on the  
surface of the work. Adjust the depth stop so that the fastener head is sunk  
just below the surface of the wallboard.  
10  
 
DRIVING SELF-DRILLING/TAPPING SCREWS – MODELS 4640  
NOTE: Maximum size screws for use with this tool are #12 wood screws and 1/4"  
self-drilling/tapping screws.  
These screws drill and tap their own hole as they are driven. This differs from  
self-tapping screws in that pre-drilled holes for tapping are not required. To drive  
these screws:  
1. Install the proper nutsetter that fits the screw to the screwdriver.  
2. Set the screwdriver for the correct rotation.  
3. Start the screwdriver and insert the head of the screw in the nutsetter.  
Do not exert pressure on the screw while performing this operation.  
4. Place the end of the screw in the desired location and remove your fingers.  
5. Apply forward pressure to drive screw until depth stop rests on the surface  
of the work. Adjust the depth stop so that the fastener head seats firmly on  
the work. Avoid seating the fastener too deep to prevent shearing off the  
head.  
TO REMOVE SCREWS – ALL MODELS  
1. Remove the Depth Stop Assembly.  
2. Install a proper bit that fits the screw.  
3. Set the screwdriver for reverse rotation.  
4. Place the bit on the screw and apply forward pressure.  
5. Start the screwdriver.  
TROUBLESHOOTING  
For assistance with your tool, visit our website at www.porter-cable.com for a  
list of service centers or call the Porter-Cable help line at 1-800-487-8665.  
MAINTENANCE  
CHECK CLUTCH CONDITION  
DISCONNECT TOOL FROM POWER SOURCE.  
A
Periodically, check the screwdriver  
clutch jaws for wear by removing the  
screwdriver mechanism housing (A)  
Fig. 5 from the power unit.  
Fig. 5  
11  
 
NOTE: The clutch housing is attached to the power unit with left-hand threads.  
Remove the depth-stop assembly from the clutch housing by pulling it straight  
off. Remove the clutch housing by turning the clutch housing clockwise.  
NOTE: Be careful not to lose the small spring that is in the end of the power unit  
spindle shaft.  
Note the condition of the 3-jaw clutch faces on the power unit and screwdriver  
mechanism. If they are badly rounded where the angular face meets the top  
surface (or appear otherwise worn or faulty), or if the clutch elements are not  
securely held in place on their respective shafts by the snap rings, return the  
entire tool to your AUTHORIZED PORTER-CABLE SERVICE STATION for  
service.  
If the jaws are not seriously worn and no other apparent faults show up in the  
mechanism, clear the mechanism and all internal areas of chips or other foreign  
material. Brush a thin coat of PORTER-CABLE gear lubricant on the clutch  
elements and surrounding areas. Attach the screwdriver mechanism to the  
power unit. Be sure the spring is in the spindle shaft.  
NOTE: The housing threads are left-hand thread.  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. All plastic parts  
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic  
parts. They could possibly dissolve or otherwise damage the material.  
Wear ANSI Z87.1 safety glasses while using compressed air.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord plug  
are making good contact in the outlet. Also, check for blown fuses or open  
circuit breakers in the line.  
LUBRICATION  
This tool has been lubricated with a sufficient amount of high grade lubricant for  
the life of the unit under normal operating conditions. No further lubrication is  
necessary.  
BRUSH INSPECTION (If applicable)  
For your continued safety and electrical protection, brush inspection and  
replacement on this tool should ONLY be performed by an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLEDELTA FACTORY  
SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest  
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.  
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes  
installed, and test the tool for performance.  
Any loss of power before the above maintenance check may indicate the need  
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL  
UNDER THIS CONDITION. If proper operating voltage is present, return your  
tool to the service station for immediate service.  
12  
 
SERVICE  
REPLACEMENT PARTS  
When servicing use only identical replacement parts. For a service parts list or to  
learn more about Porter-Cable visit our website at www.porter-cable.com  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing, or replacement of parts due to  
wear from normal use. For assistance with your tool, visit our website at  
www.porter-cable.com for a list of service centers or call the Customer Care  
Department at 1-800-487-8665. All repairs made by our service centers are fully  
guaranteed against defective material and workmanship. We cannot guarantee  
repairs made or attempted by others.  
Should you have any questions about your tool, feel free to write us at any time.  
In any communications, please give all information shown on the nameplate of  
your tool (model number, type, serial number, etc.).  
ACCESSORIES  
A complete line of accessories is available from your Porter-CableDelta  
Supplier, Porter-CableDelta Factory Service Centers, and Porter-Cable  
Authorized Service Stations. Please visit our Web Site www.porter-cable.com  
for a catalog or for the name of your nearest supplier.  
Since accessories other than those offered by  
Porter-CableDelta have not been tested with this product, use of  
such accessories could be hazardous. For safest operation, only  
Porter-CableDelta recommended accessories should be used  
with this product.  
13  
 
WARRANTY  
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary  
from state to state.  
14  
 
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
ARIZONA  
MICHIGAN  
GEORGIA  
8001 Sweet Valley Drive Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
Phoenix 85013-2906  
4501 N. 7th Ave.  
Phone: (602) 279-6414  
Fax: (602) 279-5470  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
OREGON  
Portland 97230  
14811 North East Airport Way  
Phone: (503) 255-6556  
Fax: (503) 255-6543  
MINNESOTA  
CALIFORNIA  
Eden Prairie 55344  
9709 Valley View Road  
Phone: (952) 884-9191  
Fax: (952) 884-3750  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
ILLINOIS  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
PENNSYLVANIA  
MISSOURI  
St. Louis 63146  
11477 Page Service Drive  
Phone: (314) 997-9100  
Fax: (314) 997-9183  
Willow Grove 19090 (Philadelphia)  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
San Diego 92111  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
7290 Clairemont Mesa Blvd.  
Phone: (858) 279-2011  
Fax: (858) 279-0362  
TEXAS  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
NEW YORK  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
KANSAS  
Overland Park 66214  
9201 Quivira Road  
Phone: (913) 495-4330  
Fax: (913) 495-4378  
COLORADO  
Denver 80223  
700 West Mississippi Ave.  
Phone: (303) 922-8325  
Fax: (303) 922-0245  
Houston 77022-2122  
536 East Tidwell Rd.  
Phone: (713) 692-7111  
Fax: (713) 692-1107  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
MARYLAND  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
WASHINGTON  
FLORIDA  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
OHIO  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Columbus 43229  
1948 Schrock Road  
Phone: (614) 895-3112  
Fax: (614) 895-3187  
MASSACHUSETTS  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
Tampa 33634  
4909 West Waters Ave.  
Phone: (813) 884-0434  
Fax: (813) 888-5997  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service  
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to  
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.  
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-  
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro  
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
Delta le  
plus proche.  
CANADIAN PORTER-CABLE DELTA SERVICE CENTERS  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste, Suite 160  
Québec, P.Q.  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Mtl), P.Q.  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 767-4132  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying  
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-  
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-  
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-  
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,  
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,  
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-  
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,  
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,  
WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.  
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden  
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et  
 
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  
PC7.2-0105-164  

Philips Car Stereo System CEM3000B User Manual
Philips DVD Player PET714 User Manual
Philips Electric Shaver 1250X User Manual
Philips Home Theater System LX700 User Manual
Philips Indoor Furnishings TL5 09100 User Manual
Philips MP3 Player ACT500 15 User Manual
Philips Tablet PI3000 93 User Manual
Polaroid Digital Camera M209 User Manual
Printronix Printer T5000R User Manual
Proctor Silex Dishwasher 88085 User Manual