Land Pride Lawn Mower 55 Series User Manual

Shredder Kit  
For RC(M)5515 & RC(M)6515 Rotary Cutters  
Manual No. 330-094M  
Before You Start  
Further Assistance  
Your dealer wants you to be satisfied with your new  
Shredder Kit. If for any reason you do not understand any  
part of this manual or are not satisfied with the service  
received, the following actions are suggested:  
When you see this symbol, the subsequent  
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
!
1. Discuss the matter with your dealership service  
manager making sure he is aware of any problems  
you may have and that he has had the opportunity to  
assist you.  
IMPORTANT: Before you begin, read these  
instructions and check to be sure all parts and tools  
are accounted for. Please retain these installation  
instructions for future reference and parts ordering  
information.  
2. If you are still not satisfied, seek out the owner or  
general manager of the dealership, explain the  
problem and request assistance.  
Your Shredder Kit is exclusively designed for your Land  
Pride 55 and 65 Series Rotary Cutter. Please read these  
installation instructions and your Rotary Cutter  
Operator’s Manual thoroughly before beginning.  
Especially read information relating to safety concerns.  
Also included in the Operator’s Manual is important  
information on operation, adjustment, troubleshooting,  
and maintenance for this attachment (some manual  
sections do not apply to all accessories).  
3. For further assistance write to:  
Land Pride Service Department  
1525 East North Street  
P.O. Box 5060  
Salina, Ks. 67402-5060  
E-mail address  
A separate Rotary Cutter Parts Manual is available free  
from your nearest Land Pride dealer. Have the model  
and serial numbers of your cutter handy when placing an  
order.  
Safety Information  
!
WARNING  
Never work under equipment supported by hydraulics.  
Hydraulics can drop equipment if controls are actuated or if  
hydraulic lines burst. Either situation can drop the cutter  
instantly even when power to the hydraulics is shut off.  
Manual Part Numbers:  
Operator’s Manual . . . . . . . . . . . . . . . . . 318-721M  
Parts Manual . . . . . . . . . . . . . . . . . . . . . 318-721P  
General Information  
!
DANGER  
These assembly instructions apply to the Shredder Kit  
listed below:  
Always disconnect main driveline from tractor PTO before  
servicing the cutter deck. Cutter can be engaged if tractor is  
started resulting in damage to the cutter, bodily injury and/or  
death.  
330-094A RC(M)5515 & RC(M)6515 SHREDDER KIT  
NOTE: Land Pride recommends safety glasses and  
work gloves be worn while working on the Rotary  
Cutter.  
Shredder Assembly Instructions  
A detailed listing of parts for this accessory kit is provided  
on page 4. Use the list as a checklist to inventory parts  
received. Please contact your local Land Pride dealer for  
any missing hardware.  
IMPORTANT: Read “Safety Information” above  
before installing the shredder blades.  
Refer to Figure 2 on page 2:  
1. Remove all three existing blade carrier assemblies  
from the gearbox output shafts. Keep flat washers  
(D), slotted hex nuts (E) and cotter pins (F) for reuse.  
© Copyright 2007  
Printed  
8/20/07  
 
1
Land Pride  
Shredder Assembly Instructions  
1.  
2.  
Replacing Blade Spacers  
Refer to Figure 4:  
The cutting blades should not have more than 3/4" free  
vertical movement at the blade tips. If vertical movement  
exceeds 3/4", install or change to thicker spacers (#1)  
following steps 1-5.  
Check blade deflection. If vertical deflection at the  
blade tip is greater than 3/4", remove blade bolt (#4)  
and reassemble using a thicker spacer (#1). Select  
spacer thickness based on deflection. The greater  
the deflection, the thicker the spacer.  
Assemble blades by inserting 1"-8 x 4 1/2" GR8 hex  
head bolt (#4) through blade bushing (#2),  
spacer (#1), lower cutting blade (#6, #7 or #8), blade  
carrier (#3), upper flat cutting blade (#10 or #9),  
spacer (#1) and blade bushings (#2). Temporarily  
secure blade with a plain hex nut (Plain hex nut  
furnished by customer.) Draw nut up snug. Do not  
tighten.  
Order spacers (#1) and locknuts (#8) from your nearest  
Land Pride Dealer.  
IMPORTANT: Read “Safety Information” on page 1  
before disassembling the shredder blades.  
3.  
4.  
IMPORTANT: Locknuts can lose their ability to lock  
properly once removed. Always use a plain throw  
away nut during pre-assembly of spacers.  
Check blade vertical movement. If movement at the  
blade tip is greater than 3/4", remove blade bolt and  
reassemble as before except use a thicker spacer.  
Once blade deflection is correct, replace plain nut  
with supplied locknut (#5) & torque to 450 ft-lbs.  
5. Repeat instructions for “Replacing Blade Spacers”  
for the remaining shredder blade assemblies.  
IMPORTANT: Spacers (#1) are not used if vertical  
movement at the blade tip is 3/4" or less without  
spacers. However, spacers are required if vertical  
movement at the blade tips are greater than 3/4".  
Position Beveled  
Edges Down  
Blade  
Cutting  
Edges  
(#3) Left Wing Shredder Assembly  
Clockwise Rotation  
(#1) Right Wing Shredder Assembly  
Counterclockwise Rotation  
Lower Blade Cutting Edges  
Position Beveled Edges Up  
(#2) Center Deck & Shredder Assemblies  
Counterclockwise Rotation  
25603  
Figure 4  
8/20/07  
Manual No. 330-094M  
3
 
Land Pride  
Listing of Parts  
Kit No. 330-094A  
RC(M)5515 & RC(M)6515 SHREDDER ASSEMBLY  
Item Qty. Part No. Part Description  
1
1
1
1
330-094M  
330-091S  
330-092S  
330-093S  
SHREDDER KIT INSTALLATION MANUAL  
1
2
3
CCW BLADES, SHREDDER 60" . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 1 on page 2)  
CCW BLADES, SHREDDER 72" . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 2 on page 2)  
CW BLADES, SHREDDER 60" . . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 3 on page 2)  
Refer to Figure 4 on page 3:  
(#1) Components for 330-091S CCW Blade Assembly (Left Wing Shredder - 60" cut)  
1
1
1
1
2
3
4
5
7
4
4
4
4
4
1
2
2
2
4
312-075D  
312-082D  
312-089D  
312-808D  
318-309D  
330-090H  
802-680C  
803-168C  
820-169C  
820-217C  
BLADE SPACER 16 GA  
BLADE SPACER 18 GA  
BLADE SPACER 20 GA.  
BLADE SPACER 24GA  
BLADE BUSHING  
BLADE BAR, SHREDDER 5515  
HHCS 1-8 X 4 1/2 PLT GR8  
NUT HEX TOP LOCK 1-8 PLT  
A maximum of four spacers  
are used per assembly.  
CUTTER BLADE 1/2X4X23 CCW  
CUTTER BLADE 1/2X4X22.5 FLAT  
10  
Refer to Figure 4 on page 3:  
(#2) Components for 330-092S CCW Blade Assembly (Center Deck Shredder - 72" cut)  
1
1
1
1
2
3
4
5
6
9
4
4
4
4
4
1
2
2
2
2
312-075D  
312-082D  
312-089D  
312-808D  
318-309D  
330-090H  
802-680C  
803-168C  
820-168C  
820-216C  
BLADE SPACER 16 GA  
BLADE SPACER 18 GA  
BLADE SPACER 20 GA.  
BLADE SPACER 24GA  
BLADE BUSHING  
BLADE BAR, SHREDDER 5515  
HHCS 1-8 X 4 1/2 PLT GR8  
NUT HEX TOP LOCK 1-8 PLT  
A maximum of four spacers  
are used per assembly.  
CUTTER BLADE 1/2X4X29 CCW  
CUTTER BLADE 1/2X4X28.5 FLAT  
Refer to Figure 4 on page 3:  
(#3) Components for 330-093S CW Blade Assembly (Right Wing Shredder - 60" cut)  
1
1
1
1
2
3
4
5
8
4
4
4
4
4
1
2
2
2
4
312-075D  
312-082D  
312-089D  
312-808D  
318-309D  
330-090H  
802-680C  
803-168C  
820-170C  
820-217C  
BLADE SPACER 16 GA  
BLADE SPACER 18 GA  
BLADE SPACER 20 GA.  
BLADE SPACER 24GA  
A maximum of four spacers  
are used per assembly.  
BLADE BUSHING  
BLADE BAR, SHREDDER 5515  
HHCS 1-8 X 4 1/2 PLT GR8  
NUT HEX TOP LOCK 1-8 PLT  
CUTTER BLADE 1/2X4X23 CW  
10  
CUTTER BLADE 1/2X4X22.5 FLAT  
Corporate Office: P.O. Box 5060  
Salina, Kansas 67402-5060 USA  
Manual No. 330-094M  
 
8/20/07  
4

Krown Manufacturing Answering Machine Model Krown 100 User Manual
Kyocera Printer KM P4845w User Manual
LaCie TV Cables LaCinema Play HD User Manual
Lennox International Inc Heat Pump 61H42 User Manual
Lenovo Tablet N3S2PUK User Manual
LG Electronics DVD Player BP730 User Manual
Lightolier Indoor Furnishings VRA2G16LS26U User Manual
Listen Technologies Carrying Case LBB 4500 User Manual
Marantz Car Amplifier PM 11S3 User Manual
Metra Electronics Automobile Accessories 87 99 3052 User Manual